One of the most versatile and heavily used power tools in the home wood shop, would have to be the router. These tools are capable of so many things, you could spend an enormous amount of time learning their full potential. From cutting dado's, to making moldings, to making raised panel doors, these tools, equipped with the proper bit, can accomplish a whole host of wood working tasks.
There are a number of things to consider when buying a router. The first thing to consider would be deciding if you plan on owning more than one of these modern marvels. In most professional wood shops, dedicated routers are common. This simply means cutters, or bits, as they're commonly called are left in the router, and set to perform a certain function. These routers are not used for anything else, as once they are adjusted for a specific task, they are used only for that. It might be to rabbit the back edge of cabinets, to allow the back panel to sit in this recess, or one set up with a commonly used edging bit. The advantage of this is the time saved in changing bits and adjusting it.
Router Plunge
Obviously, a home wood shop isn't as likely to own ten or more routers, but having more than one is a very good idea. If you want to have one installed into a router table, it is very convenient to have a dedicated one. Typically, you would want a plunge router for this, and one with sufficient power to handle larger cutter sets, such as raised panel cutters, for making cabinet doors. Trying to use one of these large bits in a hand held router would be quite dangerous.
Knowing router safety is imperative, as these tools, while considered relatively safe, can do a lot of damage. Using the proper feed direction, whether using a hand held router, or a router table, is important. This isn't a big of a safety factor in a hand held router, as it is with a router table, but it is still quite important.
With a router table, feeding a board into a spinning router bit, in the same direction that the bit is turning, is likely to end up with the board being pulled out of your hands, and shot like a missile across your shop. If it were to hit someone, there is a very strong chance it would be fatal.
The feed direction in a hand held router is left to right, and in a router table, is right to left. The feed direction is opposite, since the router is held in the opposite position.
Eye protection is a must, and a mask for the dust is highly recommended. If your router has a vacuum port, it helps considerably to use it. One tool that will fill the air with dust very quickly is the router.
Some routers have a toggle type switch, so it is important to verify it is in the off position, before plugging it in. It is also important to hold a router with both hands when turning it on, as the torque in these tools can cause you to lose control of it, or have it come into contact with your body. Therefore it is best to have the router held flat onto the work surface, with the bit not coming into contact with the board, and then turning it on. Then gently bring it into contact with the work piece.
Getting the best results with a router is dependent upon a few things. First is the sharpness of the bit. Next would be the feed rate. Moving the router too slow will result in burn marks on the board. Moving the router too fast, will not only put unnecessary strain on the motor, bit it will result in a poor cut. It will either be wavy, or will have tear out. The best feed rate will take some experimenting, and it will be different for various woods, and also for different router bits.
The learning curve for using a router is relatively small for the basics uses, but with all the possibilities these tools provide, you can spend a considerable amount of time mastering them.
Special Price!!! New 2HP Plunge Router Woodworking Tools Power Tools 1/2" & 1/4" Collets
Click for larger image and other views
New 2HP Plunge Router Woodworking Tools Power Tools 1/2" & 1/4" Collets Overview
2 HP plunge router features 8.75 amps. Accepts 1/4", 3/8" and 1/2" router bits. This model plunges to one of three preset depths, or you can lock at desired level. Includes a plunge depth gauge. You also get two reducing collets (1/4", and 3/8"), adjustment wrenches, and a complete instruction manual. As an added bonus, you will also get the single wheel guide, and the straight guide with a fine fence adjuster.SAVE NOW on the special offers below!
Available In Stock. |
| This New 2HP Plunge Router Woodworking Tools Power Tools 1/2" & 1/4" Collets ships for FREE with Super Saver Shipping. |
Price : Click to Check Update Prices Please. |
